Analysis of the control points of the quality of book covers

In the book cover and other printed products after the film after the product often appear bright or blistering, wrinkling and other phenomena. Now talk about the handling of common problems in operation.

1. Temperature control

In rainy or rainy seasons, if the temperature is not adjusted properly, the film products will not shine. There is noticeable water vapor on the silicone roller, which is caused by the paper absorbing a large amount of moisture. At this time, the temperature of the hot roller can be adjusted to 40 degrees Celsius. If the temperature is too high, it will blistering. Some hydrosol laminating machines do not have a heating device. It is necessary to add a drying lamp before pressing to dry the adhesive layer and reduce foaming.

2. Pressure control

When laminating, the pressure should be adjusted according to the thickness of the paper, generally at 5Pa. If the pressure is too high, wrinkles and paper deformation will occur.

3. Glue control

The glue control is controlled by the gap size of the sizing roller and the gluing roller, and the scraping film is added. Scratch film pressure light glue, pressure heavy rubber volume. The quantity of glue should be mastered, and it can be evenly covered without producing crystal spots. If the amount of glue is too large, the product will not be shiny. During the gluing process, care must be taken to prevent the tiny particles and impurities that remain after the gel from sticking to the rubber disc. If it is stuck on the film, it will produce a white offset, causing linear foaming. Before using the machine, use alcohol solvent to clean the rubber roller and the rubber bucket. If the rubber roller is not cleaned, it will cause pinholes. The glue containing impurities can be diluted with water. After the impurities are precipitated, the diluent can be used to reduce the waste of glue.

4. Roller cleaning

When paper separation occurs, the glue will directly roll on the silicone drum, causing accumulation, easy to wrinkle the product, or affect the brightness of the product, should clean the drum frequently and keep it clean. The drum itself will wrinkle when it is not even, and it needs to be replaced.

5. Control of temperature and humidity

The environmental temperature and humidity change greatly, and the paper absorbs moisture to generate “foliage”. When the film is covered, the paper is easy to wrinkle, and the balance of temperature and humidity should be maintained. The temperature of the heating roller is too high, the tight edges of the paper will wrinkle, and the temperature must be controlled as required.

6. Paper control

Paper skew will make the paper wrinkle, operation should be serious, so that the paper delivery service, the same pressure on both sides. When feeding paper, strive to stack 3mm per sheet of paper and control the amount of glue to prevent overflow. This can reduce the mutual adhesion of products after the film is covered. If the connection is wrinkled or cavitation, the pressure should be increased appropriately to maintain the temperature and humidity balance, so that the adhesion can be reduced and foaming can be reduced.

7. Film roll control

Prevent wrinkles caused by the inconsistent elasticity of both sides of the film roll. First, select the two sides of the elastic film, and then adjust the tension on both sides of the film to make it balanced to prevent wrinkles. When using a film, try to use a film with a size larger than the open size, such as a large format, use a 44-mm wide film instead of a 460-mm wide film, which saves 4% in cost. When the 780mm wide film is used for copying, it is necessary to trim the edges to reduce the amount of glue and save the glue.

8. Printing Do not use additives to control the amount of dusting

Do not use additives as much as possible during the printing process, because it is not easy to dry, easy to blistering after coating. And also need to control the amount of dusting. Before the film is coated, special personnel should be arranged to wipe off the powder on the cover to reduce the phenomenon of blooming or blistering of the film and make the product bright.

9. Speed ​​control

During the laminating process, do not arbitrarily change the speed of the host. The speed is too fast. The adhesive cannot reach the requirements. When the speed is slightly increased, the amount of glue is too large. If the speed is adjusted too low, the amount of glue is reduced and it is easy to foam. In order to ensure that the amount of glue is basically the same, the speed of the laminating machine can be limited by the maximum speed of 60% so that each class can run at a specified speed and data management can be implemented to reduce unnecessary losses.

Three-sides sealing bags are one of the most common plastic bags. It is a high barrier bag made of plastic film. The bag usually consists of 4 sides, 3 of which have been heating sealed, leaving aside for the product. The three-sides sealing bag of  Gonfor Package can be printed up to 12 colors,  width reach to 125cm, and can be used for heavy packaging of 25KG.

High-quality packaging is not only the outerwear of the product but also the bridge between the enterprise and the consumer.

Three Sides Sealing Bag

Three Sides Sealing Bag, Flat Sealing Pouch, Seeds Packaging Bag

ZHEJIANG GONFOR SOFT-PACKAGE CO.,LTD , https://www.chinasoftpackage.com

This entry was posted in on